Finned Tubes | Fin Tube Manufacturer, Supplier & Exporter for Heat Exchangers, Boilers & Air Coolers
Finned tubes (also called fin tubes) are heat-exchanger tubes with spiral, serrated, longitudinal or integral fins on the outside surface to increase heat transfer between a gas and the fluid inside the tube. ASC LLP, Mumbai, supplies finned tubes in every common fin design – HFW spiral, serrated, extruded, embedded G-type, L / LL / KL, integral low-fin and studded – on carbon steel, alloy steel, stainless steel and copper-alloy base tubes, for heat exchangers, boilers, HRSGs and air coolers worldwide.
What Are Finned Tubes?
A finned tube is a base tube with fins attached to, or formed from, its outer surface. Gas and air transfer heat far less efficiently than water, steam or oil, so the gas side usually limits a heat exchanger’s performance. Fins multiply the outside surface area – typically by 5 to 15 times – so the same duty needs fewer tubes, a smaller bundle and less steel.
A finned tube is defined by three choices:
- Base tube material – carbon steel, alloy steel, stainless steel, copper alloy or nickel alloy, chosen for pressure, temperature and corrosion.
- Fin type – how the fin is attached (welded, extruded, embedded, wrapped or integral), which sets the temperature limit and bond strength.
- Fin geometry – fin height, thickness and pitch (FPI), which balance heat transfer against pressure drop and fouling.
Buyers also search for this product as:
- Fin Tubes and Finned Tube Heat Exchangers
- Spiral Finned Tubes / Helical Finned Tubes
- Serrated Finned Tubes and HFW Finned Tubes
- Extruded Finned Tubes and G-Type Embedded Finned Tubes
- L, LL & KL Finned Tubes
- Economizer Finned Tubes and Air Cooler Fin Tubes
Types of Finned Tubes We Supply
HFW Solid Spiral Finned Tubes
- Continuous fin strip high-frequency welded to the tube
- High temperature and high gas velocity – economizers, boilers, fired heaters
HFW Serrated Finned Tubes
- Segmented fins for higher turbulence and heat transfer
- Standard in HRSGs and waste heat boilers
Extruded Finned Tubes
- Aluminium fins extruded from a sleeve over the base tube – excellent corrosion protection
- Most common in API 661 air-cooled heat exchangers
Embedded G-Type Finned Tubes
- Aluminium fin wound into a groove in the tube wall
- High bond strength for air coolers up to about 400 °C
L, LL & KL Wrapped Finned Tubes
- Tension-wound aluminium or copper fins with an L-shaped foot (LL overlapped, KL knurled)
- Economical choice for HVAC and lower-temperature air coolers
Integral Low-Fin Tubes
- Fins rolled from the tube wall itself (ASTM A498 for carbon steel)
- Shell-and-tube exchangers, condensers and evaporators
H-Type (Square) Finned Tubes
- Twin rectangular fin plates welded across one or two tubes
- Compact, wear-resistant economizers for dusty flue gas
Longitudinal Finned Tubes & Studded Tubes
- Straight fins for double-pipe exchangers and tank heaters
- Studded tubes for fired heaters with heavy-fouling flue gas

Finned Tubes by Base Tube Material
Carbon Steel Finned Tubes
- ASTM A179, A192, A210, A106, A214 and EN 10216-2 P235GH / P265GH base tubes
- Lowest cost – economizers, air coolers, HRSG low-pressure sections
Alloy Steel Finned Tubes
- ASTM A213 T11, T22, T91, T5, T9 base tubes
- High temperature and creep strength – HRSG superheaters, reheaters, fired heaters
Stainless Steel Finned Tubes
- 304 / 304L, 316 / 316L, 321, duplex 2205 base tubes
- Corrosive or condensing flue gas, food, pharma and chemical service
Copper & Copper-Nickel Finned Tubes
- Copper, 90/10 and 70/30 Cu-Ni base tubes
- HVAC, refrigeration and seawater-cooled exchangers
Nickel Alloy & Titanium Finned Tubes
- Inconel, Incoloy, Monel and titanium base tubes on request
- Highly corrosive chemical and marine service
Finned Tubes Quality Control & Testing
Every lot of finned tubes is inspected for both base tube and fin quality:
- Base tube mill test certificate to its material standard (chemistry, mechanical, hydro / NDT)
- PMI of alloy and stainless steel base tubes
- Fin bond / weld strength check (pull or peel test)
- Fin height, thickness, pitch and bare-end length checks
- Visual inspection of fin straightness and bond continuity
- Hydrostatic test of finished tubes, U-bends or coils on request
- Optional: cut-section examination, third-party inspection (TÜV, BV, SGS, Lloyd’s, DNV)
Finned tubes are supplied with EN 10204 3.1 / 3.2 base tube certificates and a finning inspection report.


Specifications Table – Finned Tubes
| Parameter | Details |
| Base Tube Materials | Carbon steel, alloy steel (T11, T22, T91), stainless steel (304, 316, duplex), copper, Cu-Ni, nickel alloys |
| Base Tube OD | 15.88 mm to 219 mm |
| Base Tube Wall Thickness | 1.0 mm to 16 mm |
| Fin Types | HFW solid, HFW serrated, extruded, embedded (G), L / LL / KL, integral low-fin, H-type, longitudinal, studded |
| Fin Materials | Carbon steel, stainless steel (409, 410S, 304, 316), aluminium (1050, 1060, 1100), copper |
| Fin Height | 6 mm to 38 mm |
| Fin Thickness | 0.3 mm to 4 mm |
| Fin Pitch | 2 to 11 FPI (approx. 79 to 433 fins per metre) |
| Tube Length | Up to 20 m (longer on request) |
| Forms | Straight with bare ends, U-bent, serpentine coils, HRSG harps |
| Test Certificate | EN 10204 3.1 / 3.2 with finning inspection report |
Finned Tube Base Tube Materials
| Base Tube Material | Common Grades | Approx. Max Tube Temperature* | Best For |
| Carbon steel | A179, A192, A210 A-1, A106 B, P235GH, P265GH | approx. 425–450 °C | Economizers, air coolers |
| Low-temperature carbon steel | A334 Grade 6 | Down to −45 °C | Sub-zero gas coolers |
| Alloy steel | A213 T11, T22, T91, T5, T9 | approx. 550–620 °C | Superheaters, reheaters, fired heaters |
| Stainless steel | 304, 316, 321, duplex 2205 | High (by grade) | Corrosive or condensing gas |
| Copper / Cu-Ni | C12200, 90/10, 70/30 | approx. 200 °C | HVAC, refrigeration, seawater |
*Typical practical limits; the allowable temperature for your design comes from the code. See carbon steel finned tubes, alloy steel finned tubes, P265GH tubes and ASTM A334 Grade 6 tubes for details.
Fin Type Selection Chart
| Fin Type | Fin Material | Max Operating Temperature (approx.) | Corrosion Protection of Tube | Typical Use |
| L (wrapped) | Aluminium / copper | 150 °C | Medium | HVAC, low-temperature air coolers |
| LL (overlapped) | Aluminium / copper | 180 °C | High | Humid or coastal air |
| KL (knurled) | Aluminium / copper | 260 °C | Medium | Higher-temperature air coolers |
| Extruded | Aluminium | 285 °C | High | API 661 air-cooled heat exchangers |
| Embedded (G) | Aluminium / copper / steel | 400 °C | Low | High-temperature air coolers |
| HFW solid / serrated | Carbon steel | approx. 450 °C | Low | Economizers, HRSG, fired heaters |
| HFW solid / serrated | Stainless steel (409, 410S, 304) | approx. 600 °C and above | Good | Superheaters, hot or corrosive gas |
Temperature limits are typical industry values for the fin bond and fin material; confirm with the thermal design.
Fin Pitch Conversion Chart – FPI, Fins per Metre and Pitch
| Fins per Inch (FPI) | Fins per Metre (FPM) | Fin Pitch (mm) |
| 2 | 79 | 12.70 |
| 3 | 118 | 8.47 |
| 4 | 157 | 6.35 |
| 5 | 197 | 5.08 |
| 6 | 236 | 4.23 |
| 7 | 276 | 3.63 |
| 8 | 315 | 3.17 |
| 10 | 394 | 2.54 |
| 11 | 433 | 2.31 |
Fin pitch = 25.4 ÷ FPI. Fired heaters use 2–4 FPI, HRSGs and economizers 3–6 FPI, and air coolers 8–11 FPI.
How Finned Tubes Improve Heat Transfer
The gas-side film is the weakest link in a gas-to-liquid heat exchanger. Fins enlarge that surface so more heat passes through each metre of tube:
- Fin height: taller fins add area, with gradually lower fin efficiency.
- Fin pitch: closer fins add area but raise pressure drop and fouling – dirty gas needs wider pitch.
- Fin thickness and material: thicker or more conductive (aluminium, copper) fins carry heat more efficiently.
- Solid vs serrated: serrated fins break up the boundary layer for higher heat transfer; solid fins are easier to clean.
- Bond quality: a welded, extruded or embedded bond avoids contact resistance between fin and tube.
How Finned Tubes Are Made
- High frequency welding (HFW): fin strip wound helically and forge-welded to the tube by HF current – solid or serrated.
- Extrusion: an aluminium sleeve over the base tube is rolled into fins, bonding tightly to the tube.
- Embedding (G-fin): a helical groove is machined in the tube wall, the fin is wound in and the groove is peened closed.
- Tension wrapping (L, LL, KL): a footed fin strip is wound under tension; KL feet are knurled into the tube surface.
- Integral rolling (low-fin): fins are cold-rolled out of the tube wall itself.
- Plate welding (H-type) and stud welding: fin plates or studs are welded onto the tube.
Every process leaves fin-free bare ends for welding into headers or rolling into tube sheets.
How to Choose the Right Finned Tube
| Application | Recommended Fin Type | Recommended Base Tube |
| Air-cooled heat exchanger (refinery / gas plant) | Extruded aluminium or embedded G-fin | Carbon steel A179 / A214, stainless on request |
| Boiler economizer | HFW solid or serrated, H-type for dusty gas | Carbon steel A192 / A210 / P265GH |
| HRSG economizer / LP evaporator | HFW serrated, carbon steel fins | Carbon steel A192 / A210 / A106 |
| HRSG HP superheater / reheater | HFW serrated, 409 / 410S fins | Alloy steel T22 / T91 |
| Fired-heater convection section | HFW solid fins or studs | Carbon steel, T5 / T9 for hot rows |
| HVAC and low-temperature air heating | L, LL or KL wrapped | Carbon steel or copper |
| Condenser / shell-and-tube exchanger | Integral low-fin | Carbon steel, copper alloy, stainless |
Send us your operating temperature, gas condition and pressure drop limits, and we will recommend the fin type and base tube.
Standards & Codes for Finned Tubes
| Standard / Code | Covers |
| ASTM A179, A192, A210, A106, A214 | Carbon steel base tubes |
| ASTM A213 / ASME SA213 | Alloy and stainless steel base tubes |
| EN 10216-2 | Seamless pressure tubes (P235GH, P265GH, 16Mo3, 13CrMo4-5) |
| ASTM A498 | Carbon steel heat-exchanger tubes with integral fins |
| API 661 | Air-cooled heat exchangers |
| API 560 | Fired heaters |
| ASME Section I / VIII, EN 12952 | Boilers, HRSGs and pressure vessels |
Applications of Finned Tubes
Finned tubes are used wherever heat must move efficiently between a gas and a liquid or steam:
- Boiler economizers, superheaters and air preheaters
- Heat recovery steam generators (HRSG) and waste heat boilers
- Air-cooled heat exchangers (fin-fan coolers) in refineries and gas plants
- Fired-heater convection sections
- Gas turbine, engine and furnace exhaust heat recovery
- HVAC, air heating and drying coils
- Refrigeration condensers and evaporators
- Process gas coolers, charge-air coolers and shell-and-tube heat exchangers
Why Choose Us as Your Finned Tubes Supplier?
With decades of experience in boiler and heat-exchanger tubes, we supply finned tubes that match your thermal design and code requirements:
- Since 1984: a long record of supplying carbon, alloy and stainless tubes
- One source: every fin type on every common base tube material
- Certified base tubes: ASTM, ASME and EN grades with EN 10204 3.1 / 3.2 certificates
- Made to drawing: custom fin height, pitch, bare ends, U-bends, coils and HRSG harps
- Technical support: help choosing fin type and material for your service
- Export-ready packing: fin-protecting spacers and seaworthy wooden crates
From air-cooler bundles to HRSG modules, our finned tubes deliver efficient heat transfer at a competitive price.
Related Products
Frequently Asked Questions – Finned Tubes
What are finned tubes?
Finned tubes are heat-exchanger tubes with fins on their outer surface. The fins increase the outside heat-transfer area – typically 5 to 15 times – so heat moves more efficiently between a gas (air or flue gas) and the fluid inside the tube.
What are the different types of finned tubes?
The main types are high frequency welded (HFW) solid and serrated spiral fin tubes, extruded fin tubes, embedded G-type fin tubes, wrapped L, LL and KL fin tubes, integral low-fin tubes, longitudinal fin tubes, H-type (square) fin tubes and studded tubes.
Which materials are finned tubes made from?
Base tubes are made from carbon steel (ASTM A179, A192, A106), alloy steel (ASTM A213 T11, T22, T91), stainless steel (304, 316, duplex), copper and copper-nickel, or nickel alloys. Fins are carbon steel, stainless steel, aluminium or copper, chosen by temperature and environment.
What is the difference between solid and serrated finned tubes?
Solid fins are a continuous helical strip with lower pressure drop and easier cleaning. Serrated fins are cut into segments, giving higher turbulence and heat transfer in a more compact bundle; they are standard in HRSGs.
Which finned tube is best for air-cooled heat exchangers?
Extruded aluminium fin tubes are the most common for air-cooled heat exchangers because the aluminium sleeve protects the base tube from atmospheric corrosion. Embedded G-fin tubes are used for higher temperatures, and L or KL fin tubes for low-temperature, cost-sensitive service.
Which finned tube is used in boiler economizers and HRSGs?
Boiler economizers and HRSGs mainly use HFW solid or serrated spiral fin tubes – carbon steel for economizer and low-pressure sections, and alloy steel (T11, T22, T91) with stainless fins for superheaters and reheaters.
What does FPI mean for finned tubes?
FPI means fins per inch along the tube. For example, 5 FPI equals a fin pitch of about 5.1 mm or about 197 fins per metre. Higher FPI gives more surface area but more pressure drop and fouling risk.
What is the maximum operating temperature of finned tubes?
It depends on fin type and material. Wrapped aluminium L-fins are limited to about 150 °C, extruded aluminium fins to about 285 °C and embedded G-fins to about 400 °C. Welded carbon steel fins are typically used up to about 450 °C, and stainless steel fins above that.
Which standards apply to finned tubes?
The base tube follows its own material standard, such as ASTM A179, A192, A213 or EN 10216-2. ASTM A498 covers carbon steel tubes with integral fins. Equipment is designed to API 661 (air coolers), API 560 (fired heaters), ASME Section I / VIII or EN 12952.
How do I specify a finned tube enquiry?
Give the base tube specification and grade, OD and wall thickness, tube length, fin type, fin material, fin height, fin thickness, fin pitch (FPI or FPM), bare-end lengths, bends or coils, quantity, and any testing or inspection requirements.

