EN 10216-2 P265GH Tube Manufacturer, Supplier & Exporter in India
EN 10216-2 P265GH tubes (material number 1.0425) are seamless non-alloy steel tubes for pressure purposes with specified properties at elevated temperatures. They are widely used in boilers, superheaters, headers, heat exchangers and steam lines in power plants, refineries and process industries. We supply P265GH+N seamless tubes in hot-finished and cold-drawn condition, to test category TC1 or TC2, with EN 10204 3.1 / 3.2 certificates.
Introduction to EN 10216-2 P265GH Tube
EN 10216-2 is the European standard for seamless steel tubes for pressure purposes – Part 2 covers non-alloy and alloy steel tubes with specified elevated-temperature properties. It is the standard most often used for boiler and pressure-equipment tubing in Europe and on projects designed to the Pressure Equipment Directive (PED) and EN 12952 / EN 13445.
P265GH is one of the main non-alloy grades in EN 10216-2, sitting above P235GH in strength. It combines a minimum yield strength of 265 MPa with good weldability and guaranteed proof strength up to 400 °C, which makes it a standard choice for boiler tubes and pressure parts in steam service.
We supply EN 10216-2 P265GH seamless tubes in a wide range of diameters, wall thicknesses and lengths, with third-party inspection, cut-to-length supply and export packing.
What is EN 10216-2 P265GH Material?
P265GH (1.0425) is a non-alloy carbon-manganese steel for pressure equipment. Its name follows the EN 10027 designation system:
- P – steel for pressure purposes
- 265 – minimum yield strength of 265 MPa (for wall thickness up to 16 mm)
- G – other characteristics follow
- H – specified properties at high (elevated) temperatures
Key features of P265GH tubes:
- Guaranteed 0.2% proof strength at elevated temperatures up to 400 °C
- Good weldability thanks to low carbon (0.20% max) and controlled residual elements
- Fine-grained, aluminium-killed steel supplied normalized (+N) for consistent toughness
- Impact tested, with a minimum of 40 J longitudinal at 20 °C
- Higher strength than P235GH, allowing thinner walls for the same pressure

Benefits of EN 10216-2 Grade P265GH Tube
1. Proven Elevated-Temperature Strength: EN 10216-2 guarantees minimum proof strength values from 100 °C to 400 °C, so designers can calculate wall thickness with confidence.
2. Designed for Pressure Equipment: P265GH tubes are made, tested and certified for pressure purposes, and are widely used under the PED and EN boiler and pressure-vessel codes.
3. Excellent Weldability: Low carbon and a capped total of residual elements (Cr + Cu + Mo + Ni ≤ 0.70%) make P265GH+N seamless tubes easy to weld and bend.
4. Seamless Integrity: With no weld seam, the tubes have uniform properties around the circumference – important for boiler and superheater duty.
5. Cost-Effective: As a non-alloy grade, P265GH is more economical than Cr-Mo alloy tubes wherever temperatures stay within its range.
Applications of EN 10216-2 P265GH Non-Alloy Seamless Steel Tube
The elevated-temperature properties of EN 10216-2 P265GH seamless tubes make them suitable for:
- Water-tube and fire-tube boilers
- Superheaters and reheaters (lower-temperature sections)
- Boiler headers and economizers
- Pressure vessels and heat exchangers
- Steam and hot-water piping
- Thermal and waste-heat recovery power plants
- Refineries and petrochemical plants
- District heating systems
Industries choose P265GH 1.0425 seamless tubes because they give reliable strength in pressure service at an economical price.


EN 10216-2 1.0425 P265GH Seamless Steel Tubes Specifications
| Specification | Details |
| Standard | EN 10216-2 (BS EN / DIN EN 10216-2) |
| Grade | P265GH |
| Material Number | 1.0425 |
| Delivery Condition | +N (normalized) |
| Test Category | TC1 / TC2 |
| Product Type | Seamless steel tubes |
| Manufacturing | Hot finished / cold drawn |
| Outer Diameter | 6 mm to 610 mm |
| Wall Thickness | 1 mm to 60 mm |
| Length | Single random, double random, cut length |
| End Type | Plain end, bevelled end |
| Surface | Black, varnished, anti-rust oil |
| Test Certificates | EN 10204 3.1 / 3.2 |
| Third-Party Inspection | TÜV, BV, SGS, Lloyd’s, DNV |
EN 10216-2 P265GH Seamless Carbon Steel Tube Chemical Composition
The chemistry of P265GH seamless tubes is controlled for strength, weldability and fine grain size (heat analysis):
| Element | Composition (%) |
| Carbon (C) | 0.20 max |
| Silicon (Si) | 0.40 max |
| Manganese (Mn) | 1.40 max |
| Phosphorus (P) | 0.025 max |
| Sulfur (S) | 0.010 max |
| Chromium (Cr) | 0.30 max |
| Molybdenum (Mo) | 0.08 max |
| Nickel (Ni) | 0.30 max |
| Copper (Cu) | 0.30 max |
| Aluminium (Al total) | 0.020 min |
| Niobium (Nb) | 0.010 max |
| Titanium (Ti) | 0.040 max |
| Vanadium (V) | 0.02 max |
| Cr + Cu + Mo + Ni | 0.70 max |
Sulfur is 0.010% max in the current edition of EN 10216-2 (earlier editions allowed 0.020%).
Mechanical Properties of P265GH Seamless Carbon Steel Tubes
| Property | Requirement (at room temperature) |
| Tensile Strength (Rm) | 410 – 570 MPa |
| Yield Strength (ReH), wall ≤ 16 mm | 265 MPa min |
| Yield Strength (ReH), 16 < wall ≤ 40 mm | 255 MPa min |
| Yield Strength (ReH), 40 < wall ≤ 60 mm | 245 MPa min |
| Elongation (A), longitudinal | 23% min |
| Elongation (A), transverse | 21% min |
| Impact Energy (KV) at 20 °C | 40 J longitudinal / 27 J transverse, min |
Elevated-Temperature Proof Strength of P265GH Tubes
| Temperature | 100 °C | 150 °C | 200 °C | 250 °C | 300 °C | 350 °C | 400 °C |
| Rp0.2 min (MPa), wall ≤ 16 mm | 226 | 213 | 192 | 171 | 154 | 141 | 134 |
These proof strength values are the basis for wall-thickness calculations in boiler and pressure-vessel design. Values for thicker walls are slightly lower.
Manufacturing Process & Heat Treatment of EN 10216-2 P265GH Tubes
EN 10216-2 P265GH seamless tubes are made from aluminium-killed, fine-grained steel and normalized before delivery.
Manufacturing Steps:
- Steelmaking and round billet casting
- Billet heating
- Piercing into a hollow shell
- Hot rolling, with optional cold drawing for tight tolerances
- Normalizing (+N), typically at 880–940 °C followed by air cooling
- Straightening, cutting and end finishing
- Leak-tightness and non-destructive testing
- Final inspection, marking and packing
Hot-finished tubes may be normalized-formed (finish-rolled in the normalizing temperature range) instead of separately normalized, provided the properties meet the standard.
Testing & Inspection of EN 10216-2 P265GH Tube
Every EN 10216-2 P265GH tube is tested to the standard’s test category (TC1 or TC2):
- Heat (ladle) analysis, plus product analysis on request
- Tensile test at room temperature
- Impact test (KV) at 20 °C
- Flattening, ring expanding or drift expanding test
- Leak-tightness test (hydrostatic or electromagnetic)
- Dimensional and visual inspection
- Non-destructive testing for longitudinal imperfections – mandatory for TC2
- Optional: elevated-temperature tensile test, PMI, third-party inspection
TC1 vs TC2 Test Category – Key Differences
| Item | TC1 | TC2 |
| Tensile & impact tests | Yes | Yes |
| Leak-tightness test | Yes | Yes |
| NDT for longitudinal imperfections | Not mandatory | Mandatory |
| Typical use | General pressure service | Critical boiler and pressure-vessel service |
State the required test category on the purchase order. If none is stated, TC1 normally applies.
EN 10216-2 P265GH Tube Suppliers in India
As experienced suppliers of EN 10216-2 P265GH seamless carbon steel tubes, we understand what boiler makers, EPC contractors and plant owners need. We keep ready stock of common boiler-tube sizes and support project-specific sizes and testing.
Our team helps customers with:
- Grade selection between P235GH, P265GH and alloy grades
- TC1 / TC2 and optional test requirements
- Mill test certificates (EN 10204 3.1 / 3.2)
- Custom dimensions and cut lengths
- Bulk quantity and project supply
- Export documentation
P235GH vs P265GH vs Comparable Grades
| Property | EN 10216-2 P235GH | EN 10216-2 P265GH | ASTM A106 Gr B | ASTM A210 Gr A-1 |
| Product | Seamless tube | Seamless tube | Seamless pipe | Seamless boiler tube |
| Yield, min | 235 MPa | 265 MPa | 240 MPa | 255 MPa |
| Tensile | 360 – 500 MPa | 410 – 570 MPa | 415 MPa min | 415 MPa min |
| Mn, max | 1.20% | 1.40% | 0.29 – 1.06% | 0.93% max |
Equivalents are approximate – check design code requirements before substituting. The old German equivalent of P265GH is DIN 17175 St 45.8; for P235GH it is St 35.8. See our EN 10216-2 P235GH tubes for the lower-strength grade.
Why Choose Us for EN 10216-2 Grade P265GH Tubes?
We deliver pressure-grade tubing with consistent quality, complete documentation and competitive pricing.
Our Strengths
- Ready stock of common P265GH boiler-tube sizes
- Fast delivery across India and worldwide
- Material from approved European and Indian mills
- TC1 and TC2 supply with EN 10204 3.1 / 3.2 certificates
- Third-party inspection welcomed
- Custom sizes and cut lengths
- Experienced export team and secure packing
- Technical support for grade selection
As experienced EN 10216-2 P265GH tube suppliers, we serve both small orders and large project requirements.
Related Products
Our EN 10216-2 P265GH tube range is built for boilers and pressure equipment working at elevated temperatures. With guaranteed proof strength, seamless construction and full EN certification, these tubes give dependable long-term performance in critical service.
Whether you need EN 10216-2 1.0425 P265GH seamless steel tubes, P265GH+N boiler tubes or TC2 tubes for critical pressure parts, we provide quality material backed by technical support, inspection and on-time delivery.
Frequently Asked Questions – EN 10216-2 P265GH Tube
What is EN 10216-2 P265GH?
EN 10216-2 P265GH (material number 1.0425) is a non-alloy steel grade for seamless tubes used in pressure equipment at elevated temperatures, such as boilers, superheaters, headers and heat exchangers. It has a minimum yield strength of 265 MPa and a tensile strength of 410–570 MPa.
What does P265GH stand for?
P stands for steel for pressure purposes, 265 is the minimum yield strength in MPa (for wall thickness up to 16 mm), G means other characteristics follow, and H means the grade has specified properties at high (elevated) temperatures.
What is the material number of P265GH?
The EN material number of P265GH is 1.0425. The same grade name and number are used for seamless tubes (EN 10216-2), welded tubes (EN 10217-2 and EN 10217-5) and plate (EN 10028-2).
What is the difference between P235GH and P265GH?
P265GH has a higher minimum yield strength (265 MPa vs 235 MPa) and tensile strength (410–570 MPa vs 360–500 MPa) than P235GH, with a higher manganese limit (1.40% vs 1.20%). This allows thinner walls for the same design pressure.
What is the ASTM equivalent of P265GH?
There is no exact ASTM equivalent. The nearest comparable grades are ASTM A106 Grade B for pipe and ASTM A210 Grade A-1 for boiler tubes. The old German equivalent is DIN 17175 St 45.8. Always check strength, impact and elevated-temperature properties against your design code before substituting.
What does +N mean in P265GH+N?
+N means the tubes are supplied in the normalized condition, which is the standard delivery condition for P265GH in EN 10216-2. Normalizing refines the grain structure for consistent strength and toughness.
What is the difference between TC1 and TC2 for P265GH tubes?
TC1 and TC2 are test categories in EN 10216-2. TC2 adds mandatory non-destructive testing of every tube (for example ultrasonic testing for longitudinal imperfections) and extra testing. TC2 is usually specified for higher-risk pressure equipment.
What is the maximum service temperature of P265GH tubes?
EN 10216-2 gives elevated-temperature proof strength for P265GH up to 400 °C, and creep data are used above that. In practice, P265GH is used for boiler and pressure parts up to roughly 400–450 °C; above that, alloy grades such as 16Mo3 or 13CrMo4-5 are used.
Is P265GH alloy steel?
No. P265GH is a non-alloy (carbon-manganese) steel. Its strength at high temperature comes from controlled chemistry and normalizing, not from alloying elements such as chromium or molybdenum.
What sizes are available in EN 10216-2 P265GH tubes?
We supply P265GH seamless tubes from about 6 mm to 610 mm outside diameter, with wall thickness from 1 mm to 60 mm, in hot-finished or cold-drawn condition and in random or cut lengths.
Global Reach
ASC LLP supplies pressure-grade tubes to boiler makers, EPC contractors and plant owners around the world, with prompt delivery and complete documentation. Customers in the USA, Europe, the Middle East and Asia rely on our EN 10216-2 P265GH tubes for boiler and pressure-equipment projects.

Countries We Export To
UNITED STATES, EUROPE, UK, UAE, SAUDI ARABIA, OMAN, KUWAIT, JORDAN, QATAR, INDONESIA, MALAYSIA, BRAZIL, SPAIN, ITALY, FRANCE, GERMANY, BAHRAIN, SRI LANKA, AZERBAIJAN, AUSTRALIA, AUSTRIA, PHILIPPINES, TURKEY, RUSSIA, IRAN, IRAQ, CANADA, KOREA, JAPAN, YEMEN, FINLAND, ZIMBABWE, HUNGARY, PORTUGAL, VIETNAM, MOROCCO, THAILAND, SOUTH AFRICA, MEXICO, SINGAPORE, GREECE, KUWAIT, POLAND, NEW ZEALAND, SWEDEN, SWITZERLAND, BELGIUM, BHUTAN, BANGLADESH, TAIWAN, ROMANIA, CAMBODIA, KAZAKHSTAN, AFGHANISTAN.

