ASTM A334 Grade 6 Tubes | ASME SA334 Gr 6 Low Temperature Carbon Steel Tubes Supplier & Exporter

ASTM A334 Grade 6 tubes (also ordered as ASME SA334 Gr 6) are seamless and welded carbon steel tubes made for service at sub-zero temperatures. Grade 6 is the most widely specified grade in the A334 standard: a silicon-killed, fine-grained carbon-manganese steel that is Charpy impact tested at -45°C (-50°F) and offers higher strength than Grade 1.

ASC LLP, Mumbai, has supplied low temperature carbon steel (LTCS) tubes since 1984 to refineries, LNG and gas-processing plants, heat-exchanger fabricators and EPC contractors across the USA, Europe, the Middle East and South America.

What Are ASTM A334 Grade 6 Tubes?

ASTM A334/A334M is the standard specification for seamless and welded carbon and alloy-steel tubes for low-temperature service. Unlike pipe standards such as ASTM A333, A334 covers minimum-wall tubes ordered by outside diameter and minimum wall thickness – the format used for heat exchangers, condensers, instrument lines and small-bore process tubing.

Grade 6 (UNS K03006) is a plain carbon-manganese grade with a maximum of 0.30% carbon, 0.29–1.06% manganese and a minimum of 0.10% silicon. The silicon requirement makes it a fully killed steel, and normalizing gives it a fine-grained microstructure. The result is a tube with 415 MPa minimum tensile strength, 240 MPa minimum yield and dependable notch toughness down to -45°C. It is commonly supplied as:

  • ASTM A334 Grade 6 Seamless Tubes
  • ASME SA334 Gr 6 Welded / ERW Tubes
  • A334 Grade 6 Heat Exchanger Tubes
  • A334 Gr 6 U-Bend Tubes
  • LTCS A334 Grade 6 Cold Drawn Seamless (CDS) Tubes

Types of A334 Grade 6 Tubes We Supply

We supply A334 Grade 6 low temperature tubes in the forms most used by fabricators and EPC buyers:

A334 Grade 6 Seamless Tubes

  • Hot finished or cold drawn
  • First choice for high-pressure, pressure-rated and critical heat-exchanger duty

SA334 Gr 6 Welded / ERW Tubes

  • Welded without filler metal, as the specification requires
  • Impact tested across the weld as well as the base metal
  • Economical option for many standard applications

A334 Grade 6 Heat Exchanger & Condenser Tubes

  • Straight lengths cut to tube-sheet requirements
  • Tight OD and wall tolerances per ASTM A1016 for consistent tube-to-tubesheet joints

A334 Gr 6 U-Bend Tubes

  • Bent to drawing, with stress relieving of the bend zone when specified
  • Hydro tested after bending on request

A334 Grade 6 Instrumentation & Small-Bore Tubes

  • Small OD tubes and coils for sampling and instrument lines in cold service

A334 Gr 6 Tubes with NACE MR0175 / HIC Testing

  • For sour and hydrogen service, supplied with the required hardness and HIC/SSC test reports
ASTM A334 Grade 6 seamless low temperature carbon steel tubes

Seamless vs Welded A334 Grade 6 Tubes

A334 Grade 6 Seamless Tubes

  • No weld seam – uniform properties around the circumference
  • Preferred for high pressure, cyclic and critical service
  • Flare test applies

A334 Grade 6 Welded Tubes

  • Lower cost and tight wall tolerance
  • Charpy specimens taken across the weld as well as from the base metal
  • Flange and reverse flattening tests apply

Choose the type based on design pressure, your project specification and budget.

A334 Grade 6 Tubes Quality Control & Testing

Every lot of ASTM A334 Grade 6 tubes is tested to the specification and documented on the mill test certificate:

  • Chemical (heat and product) analysis
  • Tension test
  • Flattening test
  • Flare test (seamless) / flange and reverse flattening tests (welded)
  • Hardness test (Rockwell / Brinell)
  • Charpy V-notch impact test at -45°C
  • Hydrostatic test or non-destructive electric test (eddy current / ultrasonic) per ASTM A1016
  • Visual and dimensional inspection
  • Optional: PMI, HIC, NACE MR0175 / MR0103, third-party inspection (TÜV, BV, SGS, Lloyd’s, DNV)

Tubes are marked with specification, grade, size, heat number, manufacturer and the letters “LT” followed by the impact test temperature (e.g. LT-50), as required by A334.

ASME SA334 Grade 6 seamless carbon steel tubes stacked with LT-50 mill marking
ASTM A334 Grade 6 U-bend heat exchanger tubes

Specifications Table – ASTM A334 Grade 6 Tubes

Parameter Details
Standard ASTM A334 / A334M, ASME SA334 / SA334M
Grade Grade 6 (Gr. 6), UNS K03006 – carbon steel, low temperature service
General Requirements ASTM A1016 / A1016M
Type Seamless (hot finished / cold drawn), Welded (ERW)
Outside Diameter 6.35 mm (1/4″) to 168.3 mm (6″) – other sizes on request
Wall Thickness 0.89 mm to 12.7 mm (minimum wall)
Length Single random, double random, fixed lengths up to 12 m; U-bent tubes to drawing
Impact Test Temperature -45°C (-50°F); lower temperatures on request
Heat Treatment Normalized, normalized & tempered, or controlled hot-finished (seamless)
Ends Plain end, bevelled end, square cut
Surface Black / varnished, anti-rust oil, end caps
Test Certification EN 10204 3.1; 3.2 with third-party inspection on request

Chemical Composition Table – ASTM A334 Grade 6

Element Percentage (%)
Carbon (C) 0.30 max
Manganese (Mn) 0.29 – 1.06
Phosphorus (P) 0.025 max
Sulfur (S) 0.025 max
Silicon (Si) 0.10 min
Iron (Fe) Balance

For each reduction of 0.01% carbon below 0.30%, an increase of 0.05% manganese above 1.06% is permitted, up to a maximum of 1.35% Mn. The 0.10% minimum silicon makes Grade 6 a fully killed steel – the key chemical difference from Grade 1.

Mechanical Properties of ASTM A334 Grade 6 Tubes

Property Requirement
Tensile Strength, min 60 ksi (415 MPa)
Yield Strength, min 35 ksi (240 MPa)
Elongation in 2 in. (50 mm), min – longitudinal 30% (walls 8 mm / 5/16″ and over)
Elongation in 2 in. (50 mm), min – transverse 16.5%
Hardness, max Rockwell B90 / 190 HB
Charpy Impact Test Temperature -45°C (-50°F)

Minimum Elongation by Wall Thickness – A334 Grade 6 (Strip Specimens)

Wall Thickness Min. Elongation in 2 in. (50 mm)
5/16″ (8 mm) 30%
9/32″ (7.2 mm) 28%
1/4″ (6.4 mm) 27%
7/32″ (5.6 mm) 26%
3/16″ (4.8 mm) 24%
5/32″ (4 mm) 22%
1/8″ (3.2 mm) 21%
3/32″ (2.4 mm) 20%
1/16″ (1.6 mm) 18%

Values are for longitudinal strip specimens: 1.50 percentage points are deducted from the basic 30% for each 1/32″ (0.8 mm) decrease in wall thickness below 5/16″.

Impact Test Requirements for A334 Grade 6 Tubes (Charpy V-Notch at -45°C)

Impact testing is what makes A334 Grade 6 a low temperature tube. Charpy V-notch specimens are tested to ASTM E23 at -45°C. Because tube walls are often too thin for full-size specimens, A334 allows sub-size specimens with proportionally lower energy values. For welded tubes, specimens are taken from the weld as well as the base metal.

Charpy Impact Requirements – A334 Grade 6

Specimen Size (mm) Min. Average of 3 Specimens Min. for One Specimen
10 × 10 (full size) 13 ft·lbf (18 J) 10 ft·lbf (14 J)
10 × 7.5 10 ft·lbf (14 J) 8 ft·lbf (11 J)
10 × 6.67 9 ft·lbf (12 J) 7 ft·lbf (9 J)
10 × 5 7 ft·lbf (9 J) 5 ft·lbf (7 J)
10 × 3.33 5 ft·lbf (7 J) 3 ft·lbf (4 J)
10 × 2.5 4 ft·lbf (5 J) 3 ft·lbf (4 J)

Important for buyers: when the sub-size specimen width along the notch is less than 80% of the actual wall thickness, the test temperature must be lowered below -45°C by the amount set out in the specification. Very small tubes that cannot yield even the smallest sub-size specimen are exempt from impact testing. If your design needs toughness below -45°C, state the lower test temperature on the purchase order.

ASTM A334 Grades and Their Impact Test Temperatures

A334 Grade Type Impact Test Temperature
Grade 1 Carbon steel -45°C (-50°F)
Grade 6 Carbon steel (Si-killed) -45°C (-50°F)
Grade 7 2.5% nickel steel -75°C (-100°F)
Grade 9 Nickel-copper steel -75°C (-100°F)
Grade 3 3.5% nickel steel -100°C (-150°F)
Grade 8 9% nickel steel -195°C (-320°F)

Grade 6 is the standard carbon steel choice down to -45°C. For colder service, move up to a nickel-bearing grade.

Heat Treatment of ASTM A334 Grade 6 Tubes

All Grade 6 tubes must be treated to control their microstructure by one of these methods:

  • Normalizing – heating to a uniform temperature of not less than 845°C (1550°F) and cooling in air or in the cooling chamber of an atmosphere-controlled furnace.
  • Normalizing and tempering – normalized as above and, at the manufacturer’s discretion, reheated to a suitable tempering temperature.
  • Controlled hot finishing (seamless only) – hot working finished between 845–955°C (1550–1750°F) and cooled in a controlled-atmosphere furnace from not less than 845°C.

ASTM A334 Grade 6 vs Grade 1 vs A333 Grade 6

Feature A334 Grade 6 A334 Grade 1 A333 Grade 6
Product Form Tube (OD × min wall) Tube (OD × min wall) Pipe (NPS × schedule)
Carbon, max 0.30% 0.30% 0.30%
Manganese 0.29–1.06% 0.40–1.06% 0.29–1.06%
Silicon 0.10% min No requirement 0.10% min
Tensile, min 415 MPa 380 MPa 415 MPa
Yield, min 240 MPa 205 MPa 240 MPa
Hardness, max B90 / 190 HB B85 / 163 HB —
Impact Test Temp. -45°C -45°C -45°C

Which should you choose? Grade 6 and Grade 1 share the same -45°C impact temperature. Grade 6 is killed with silicon and is about 35 MPa stronger in both tensile and yield, so it is the usual choice for pressure-rated exchangers and process tubing, and it pairs with A333 Grade 6 pipe in the same LTCS piping class. Grade 1 is softer (B85 max), which can help with heavy roller expansion or very tight U-bends – see our ASTM A334 Grade 1 Tubes. For pipe sizes by schedule, see our ASTM A333 Gr 6 Low Temperature Pipes.

ASTM A334 Grade 6 Equivalent Grades

Standard Equivalent Grade
ASTM A334 Grade 6
ASME SA334 Grade 6
UNS K03006
EN (nearest) P265NL – EN 10216-4 / EN 10217-4
JIS (nearest) STBL 380 – JIS G3464
DIN (legacy) TTSt 35 N (1.0356)

Equivalents are approximate. Impact test temperatures and energy values differ between ASTM and EN standards – confirm suitability against your design code before substituting.

How to Order ASTM A334 Grade 6 Tubes

To get an accurate quote quickly, include these details in your enquiry:

  • Quantity (metres, number of lengths or tonnes)
  • Specification and grade – ASTM A334 / ASME SA334 Grade 6
  • Seamless or welded
  • Outside diameter and minimum wall thickness
  • Length – random, fixed cut, or U-bend drawing
  • Impact test temperature if lower than -45°C
  • Optional requirements – NACE / HIC, PMI, NDE method, third-party inspection
  • Certification – EN 10204 3.1 or 3.2

Applications of ASTM A334 Grade 6 Tubes

Thanks to their strength and proven toughness at -45°C, A334 Grade 6 low temperature tubes are widely used in:

  • Heat exchangers and condensers handling chilled or refrigerated process fluids
  • LNG, LPG, NGL and gas-processing plants
  • Refrigeration and ammonia plants
  • Petrochemical and refinery units – ethylene, propylene, depropanizer and blowdown services
  • Air separation units and cold boxes (carbon steel sections above -45°C)
  • Offshore and arctic installations
  • Instrument and sampling lines in cold climates

Why Choose Us as Your ASTM A334 Grade 6 Tubes Supplier?

With four decades of experience in carbon and low temperature steel tubulars, we understand what project buyers need:

  • Since 1984: a long record of supplying carbon, alloy and LTCS tubes
  • Mill-sourced material from approved Indian and international seamless tube mills
  • Full traceability: heat-wise bundling, stencilled marking, EN 10204 3.1/3.2 MTCs
  • Third-party inspection welcomed at the mill and at our Mumbai facility
  • Matched LTCS packages: A334 Gr 6 tubes alongside A333 Gr 6 pipes for the same project
  • Export-ready packing: hexagonal bundles with steel straps, end caps, wooden boxes for U-tubes

ASTM A334 Grade 6 tubes are the standard choice wherever carbon steel tubing must stay strong and tough below zero. As an experienced A334 Grade 6 tubes supplier and exporter, we focus on correct material, complete documentation and on-time delivery with every order.

Related Products

Frequently Asked Questions – ASTM A334 Grade 6 Tubes

What is ASTM A334 Grade 6?

ASTM A334 Grade 6 is a silicon-killed carbon-manganese steel grade for seamless and welded tubes intended for low-temperature service. It has a maximum of 0.30% carbon, 0.29–1.06% manganese and at least 0.10% silicon, a minimum tensile strength of 415 MPa and a minimum yield strength of 240 MPa, and it is Charpy impact tested at -45°C (-50°F).

What is the minimum design temperature for A334 Grade 6 tubes?

The standard Charpy impact test temperature for A334 Grade 6 is -45°C (-50°F). The minimum design metal temperature permitted in your system is set by the applicable design code (e.g. ASME B31.3 or ASME Section VIII), wall thickness and stress level – the test temperature alone does not fix it. For service below -45°C, nickel grades such as A334 Grade 7, 3 or 8 are used.

What is the difference between A334 Grade 6 and Grade 1?

Both are carbon steel grades impact tested at -45°C. Grade 6 requires a minimum of 0.10% silicon (fully killed) and has higher strength – 415 MPa tensile and 240 MPa yield versus 380 MPa and 205 MPa for Grade 1 – with a maximum hardness of B90 against B85 for Grade 1.

What is the difference between ASTM A334 Grade 6 and ASTM A333 Grade 6?

A334 covers tubes ordered by outside diameter and minimum wall thickness, typically for heat exchangers and small-bore lines. A333 covers pipe ordered by nominal pipe size and schedule with average wall thickness. The chemistry, tensile properties and -45°C impact requirement for Grade 6 are essentially the same in both specifications.

Is ASME SA334 Grade 6 the same as ASTM A334 Grade 6?

Yes, technically. ASME adopts the ASTM specification into the Boiler and Pressure Vessel Code as SA334. Tubes are commonly dual-certified as ASTM A334 / ASME SA334 Grade 6, which allows their use in ASME code-stamped equipment.

What is the hardness of A334 Grade 6 tubes?

The maximum hardness for A334 Grade 6 is Rockwell B90, equivalent to about 190 HB. For sour service under NACE MR0175, a lower hardness limit of 22 HRC applies to the finished tube and is easily met by normalized Grade 6.

Are A334 Grade 6 tubes available in seamless and welded form?

Yes. The specification covers both seamless and welded (without filler metal) tubes. Seamless tubes are preferred for high-pressure and critical heat-exchanger duty; welded tubes are an economical option for many standard applications.

Can A334 Grade 6 tubes be supplied as U-bend tubes?

Yes. We supply A334 Grade 6 U-bend tubes bent to customer drawings, with stress relieving of the bend area and hydrostatic testing after bending when specified.

Can A334 Grade 6 tubes be welded?

Yes. With carbon limited to 0.30% and a controlled manganese range, Grade 6 has good weldability. For low-temperature service, welding procedures should be qualified with impact testing at the design temperature, as required by ASME Section VIII and B31.3.

What certificates are supplied with A334 Grade 6 tubes?

Each supply includes an EN 10204 3.1 mill test certificate showing chemistry, mechanical, hardness, impact and hydro/NDE results. EN 10204 3.2 certification with third-party inspection by agencies such as TÜV, BV, SGS, Lloyd’s or DNV is available on request.

Follow us on: