ASTM A334 Grade 1 Tubes | ASME SA334 Gr 1 Low Temperature Carbon Steel Tubes Supplier & Exporter
ASTM A334 Grade 1 tubes (also ordered as ASME SA334 Gr 1) are seamless and welded carbon steel tubes made for service at sub-zero temperatures. Every heat-treatment lot is Charpy impact tested at -45°C (-50°F), which is what separates A334 Grade 1 from ordinary carbon steel tubing such as A179 or A192.
ASC LLP, Mumbai, has supplied low temperature carbon steel (LTCS) tubes since 1984 to refineries, LNG and gas-processing plants, heat-exchanger fabricators and EPC contractors across the USA, Europe, the Middle East and South America.
What Are ASTM A334 Grade 1 Tubes?
ASTM A334/A334M is the standard specification for seamless and welded carbon and alloy-steel tubes for low-temperature service. Unlike pipe standards such as ASTM A333, A334 covers minimum-wall tubes ordered by outside diameter and minimum wall thickness – the format used for heat exchangers, condensers, instrument lines and small-bore process tubing.
Grade 1 is the plain carbon-manganese grade of the specification: no alloying elements, a maximum of 0.30% carbon and 0.40–1.06% manganese. Its fine-grained, normalized microstructure gives reliable notch toughness down to -45°C, combined with good ductility, easy bending and straightforward weldability. It is commonly supplied as:
- ASTM A334 Grade 1 Seamless Tubes
- ASME SA334 Gr 1 Welded / ERW Tubes
- A334 Grade 1 Heat Exchanger Tubes
- A334 Gr 1 U-Bend Tubes
- LTCS A334 Grade 1 Cold Drawn Seamless (CDS) Tubes
Types of A334 Grade 1 Tubes We Supply
We supply A334 Grade 1 low temperature tubes in the forms most used by fabricators and EPC buyers:
A334 Grade 1 Seamless Tubes
- Hot finished or cold drawn
- Preferred for high-pressure and critical heat-exchanger duty
SA334 Gr 1 Welded / ERW Tubes
- Welded without filler metal, as the specification requires
- Economical option for many standard applications
A334 Grade 1 Heat Exchanger & Condenser Tubes
- Straight lengths cut to tube-sheet requirements
- Soft enough (HRB 85 max) for reliable roller expansion
A334 Gr 1 U-Bend Tubes
- Bent to drawing, with stress relieving of the bend zone when specified
- Hydro tested after bending on request
A334 Grade 1 Instrumentation & Small-Bore Tubes
- Small OD tubes and coils for sampling and instrument lines in cold service
A334 Gr 1 Tubes with NACE MR0175 / HIC Testing
- For sour and hydrogen service, supplied with the required test reports

Seamless vs Welded A334 Grade 1 Tubes
A334 Grade 1 Seamless Tubes
- No weld seam – uniform properties around the circumference
- Preferred for high pressure and critical service
- Flare test applies
A334 Grade 1 Welded Tubes
- Lower cost and tight wall tolerance
- Impact tested across the weld as well as the base metal
- Flange and reverse flattening tests apply
Choose the type based on design pressure, your project specification and budget.
A334 Grade 1 Tubes Quality Control & Testing
Every lot of ASTM A334 Grade 1 tubes is tested to the specification and documented on the mill test certificate:
- Chemical (heat and product) analysis
- Tension test
- Flattening test
- Flare test (seamless) / flange and reverse flattening tests (welded)
- Hardness test (Rockwell / Brinell)
- Charpy V-notch impact test at -45°C
- Hydrostatic test or non-destructive electric test (eddy current / ultrasonic) per ASTM A1016
- Visual and dimensional inspection
- Optional: PMI, HIC, NACE MR0175 / MR0103, third-party inspection (TÜV, BV, SGS, Lloyd’s, DNV)
Tubes are marked with specification, grade, size, heat number, manufacturer and the letters “LT” followed by the impact test temperature (e.g. LT-50), as required by A334.


Specifications Table – ASTM A334 Grade 1 Tubes
| Parameter | Details |
| Standard | ASTM A334 / A334M, ASME SA334 / SA334M |
| Grade | Grade 1 (Gr. 1) – carbon steel, low temperature service |
| General Requirements | ASTM A1016 / A1016M |
| Type | Seamless (hot finished / cold drawn), Welded (ERW) |
| Outside Diameter | 6.35 mm (1/4″) to 168.3 mm (6″) – other sizes on request |
| Wall Thickness | 0.89 mm to 12.7 mm (minimum wall) |
| Length | Single random, double random, fixed lengths up to 12 m; U-bent tubes to drawing |
| Impact Test Temperature | -45°C (-50°F) |
| Heat Treatment | Normalized, normalized & tempered, or controlled hot-finished (seamless) |
| Ends | Plain end, bevelled end, square cut |
| Surface | Black / varnished, anti-rust oil, end caps |
| Test Certification | EN 10204 3.1; 3.2 with third-party inspection on request |
Chemical Composition Table – ASTM A334 Grade 1
| Element | Percentage (%) |
| Carbon (C) | 0.30 max |
| Manganese (Mn) | 0.40 – 1.06 |
| Phosphorus (P) | 0.025 max |
| Sulfur (S) | 0.025 max |
| Silicon (Si) | No requirement |
| Iron (Fe) | Balance |
For each reduction of 0.01% carbon below 0.30%, an increase of 0.05% manganese above 1.06% is permitted, up to a maximum of 1.35% Mn.
Mechanical Properties of ASTM A334 Grade 1 Tubes
| Property | Requirement |
| Tensile Strength, min | 55 ksi (380 MPa) |
| Yield Strength, min | 30 ksi (205 MPa) |
| Elongation in 2 in. (50 mm), min | 35% (walls 8 mm / 5/16″ and over) |
| Hardness, max | Rockwell B85 / 163 HB |
| Charpy Impact Test Temperature | -45°C (-50°F) |
Minimum Elongation by Wall Thickness – A334 Grade 1 (Strip Specimens)
| Wall Thickness | Min. Elongation in 2 in. (50 mm) |
| 5/16″ (8 mm) | 35% |
| 9/32″ (7.2 mm) | 33% |
| 1/4″ (6.4 mm) | 32% |
| 7/32″ (5.6 mm) | 30% |
| 3/16″ (4.8 mm) | 28% |
| 5/32″ (4 mm) | 26% |
| 1/8″ (3.2 mm) | 25% |
| 3/32″ (2.4 mm) | 23% |
| 1/16″ (1.6 mm) | 21% |
Impact Test Requirements for A334 Grade 1 Tubes (Charpy V-Notch at -45°C)
Impact testing is the defining requirement of A334 Grade 1. Charpy V-notch specimens are tested to ASTM E23 at -45°C. Because tube walls are often too thin for full-size specimens, A334 allows sub-size specimens with proportionally lower energy values.
Charpy Impact Requirements – A334 Grade 1
| Specimen Size (mm) | Min. Average of 3 Specimens | Min. for One Specimen |
| 10 × 10 (full size) | 13 ft·lbf (18 J) | 10 ft·lbf (14 J) |
| 10 × 7.5 | 10 ft·lbf (14 J) | 8 ft·lbf (11 J) |
| 10 × 6.67 | 9 ft·lbf (12 J) | 7 ft·lbf (9 J) |
| 10 × 5 | 7 ft·lbf (9 J) | 5 ft·lbf (7 J) |
| 10 × 3.33 | 5 ft·lbf (7 J) | 3 ft·lbf (4 J) |
| 10 × 2.5 | 4 ft·lbf (5 J) | 3 ft·lbf (4 J) |
Important for buyers: when the sub-size specimen width along the notch is less than 80% of the actual wall thickness, the test temperature must be lowered below -45°C by the amount set out in the specification. Very small tubes that cannot yield even the smallest sub-size specimen are exempt from impact testing.
Heat Treatment of ASTM A334 Grade 1 Tubes
All Grade 1 tubes must be treated to control their microstructure by one of these methods:
- Normalizing – heating to a uniform temperature of not less than 845°C (1550°F) and cooling in air or in the cooling chamber of an atmosphere-controlled furnace.
- Normalizing and tempering – normalized as above and, at the manufacturer’s discretion, reheated to a suitable tempering temperature.
- Controlled hot finishing (seamless only) – hot working finished between 845–955°C (1550–1750°F) and cooled in a controlled-atmosphere furnace from not less than 845°C.
ASTM A334 Grade 1 vs Grade 6 vs A333 Grade 1
| Feature | A334 Grade 1 | A334 Grade 6 | A333 Grade 1 |
| Product Form | Tube (OD × min wall) | Tube (OD × min wall) | Pipe (NPS × schedule) |
| Carbon, max | 0.30% | 0.30% | 0.30% |
| Manganese | 0.40–1.06% | 0.29–1.06% | 0.40–1.06% |
| Silicon | No requirement | 0.10% min | No requirement |
| Tensile, min | 380 MPa | 415 MPa | 380 MPa |
| Yield, min | 205 MPa | 240 MPa | 205 MPa |
| Hardness, max | B85 / 163 HB | B90 / 190 HB | — |
| Impact Test Temp. | -45°C | -45°C | -45°C |
Which should you choose? Grade 1 and Grade 6 share the same -45°C impact temperature. Grade 6 is a silicon-killed steel with higher strength, so it is the more common choice for pressure-rated designs. Grade 1, being softer (B85 max), is often preferred where tubes are expanded into tube sheets or cold bent into tight U-bends. For pipe sizes by schedule, see our ASTM A333 Gr 6 Low Temperature Pipes.
ASTM A334 Grade 1 Equivalent Grades
| Standard | Equivalent Grade |
| ASTM | A334 Grade 1 |
| ASME | SA334 Grade 1 |
| UNS | K03008 |
| EN (nearest) | P215NL – EN 10216-4 / EN 10217-4 |
| JIS | STBL 380 |
| DIN (legacy) | TTSt 41 N (1.0437) |
Equivalents are approximate. Impact test temperatures and energy values differ between ASTM and EN standards – confirm suitability against your design code before substituting.
Applications of ASTM A334 Grade 1 Tubes
Thanks to their proven toughness at -45°C, A334 Grade 1 low temperature tubes are widely used in:
- Heat exchangers and condensers handling chilled or refrigerated process fluids
- LNG, LPG and gas-processing plants
- Refrigeration and ammonia plants
- Petrochemical and refinery units – ethylene, propylene and blowdown services
- Air separation units and cold boxes (carbon steel sections above -45°C)
- Offshore and arctic installations
- Instrument and sampling lines in cold climates
Why Choose Us as Your ASTM A334 Grade 1 Tubes Supplier?
With four decades of experience in carbon and low temperature steel tubulars, we understand what project buyers need:
- Since 1984: a long record of supplying carbon, alloy and LTCS tubes
- Mill-sourced material from approved Indian and international seamless tube mills
- Full traceability: heat-wise bundling, stencilled marking, EN 10204 3.1/3.2 MTCs
- Third-party inspection welcomed at the mill and at our Mumbai facility
- Export-ready packing: hexagonal bundles with steel straps, end caps, wooden boxes for U-tubes
ASTM A334 Grade 1 tubes are a dependable choice wherever carbon steel tubing must stay tough below zero. As an experienced A334 Grade 1 tubes supplier and exporter, we focus on correct material, complete documentation and on-time delivery with every order.
Frequently Asked Questions – ASTM A334 Grade 1 Tubes
What is ASTM A334 Grade 1?
ASTM A334 Grade 1 is a carbon-manganese steel grade for seamless and welded tubes intended for low-temperature service. It has a maximum of 0.30% carbon and 0.40–1.06% manganese, a minimum tensile strength of 380 MPa and a minimum yield strength of 205 MPa, and it is Charpy impact tested at -45°C (-50°F).
What is the minimum design temperature for A334 Grade 1 tubes?
The standard Charpy impact test temperature for A334 Grade 1 is -45°C (-50°F). The minimum design metal temperature permitted in your system is set by the applicable design code (e.g. ASME B31.3 or ASME Section VIII), wall thickness and stress level – the test temperature alone does not fix it.
What is the difference between A334 Grade 1 and Grade 6?
Both are carbon steel grades impact tested at -45°C. Grade 6 requires a minimum of 0.10% silicon and has higher strength (415 MPa tensile, 240 MPa yield) and a higher maximum hardness (B90). Grade 1 is softer (B85 max), which helps when tubes are roller-expanded into tube sheets or tightly bent.
What is the difference between ASTM A334 and ASTM A333?
A334 covers tubes ordered by outside diameter and minimum wall thickness, typically for heat exchangers and small-bore lines. A333 covers pipe ordered by nominal pipe size and schedule with average wall thickness. The chemistry and impact requirements for Grade 1 are essentially the same in both specifications.
Is ASME SA334 Grade 1 the same as ASTM A334 Grade 1?
Yes, technically. ASME adopts the ASTM specification into the Boiler and Pressure Vessel Code as SA334. Tubes are commonly dual-certified as ASTM A334 / ASME SA334 Grade 1, which allows their use in ASME code-stamped equipment.
Are A334 Grade 1 tubes available in seamless and welded form?
Yes. The specification covers both seamless and welded (without filler metal) tubes. Seamless tubes are preferred for high-pressure and critical heat-exchanger duty; welded tubes are an economical option for many standard applications.
Can A334 Grade 1 tubes be supplied as U-bend tubes?
Yes. We supply A334 Grade 1 U-bend tubes bent to customer drawings, with stress relieving of the bend area and hydrostatic testing after bending when specified.
What certificates are supplied with A334 Grade 1 tubes?
Each supply includes an EN 10204 3.1 mill test certificate showing chemistry, mechanical, hardness, impact and hydro/NDE results. EN 10204 3.2 certification with third-party inspection by agencies such as TÜV, BV, SGS, Lloyd’s or DNV is available on request.

