AA 5054 Aluminium Pipes & Tubes – Grade Guide, Specs & Supply
What are AA 5054 pipes?
“AA 5054” is a trade name used for aluminium-magnesium (5xxx series) pipes. 5054 is not a registered Aluminum Association grade and is not listed in ASTM B221, ASTM B241 or EN 573-3. Buyers who ask for 5054 pipe normally need one of two standard grades:
- AA 5454 (UNS A95454) – about 2.7% Mg and 0.8% Mn; listed in ASTM B241 / B221 for pipe and tube.
- EN AW-5754 (AlMg3, 3.3535) – about 3.1% Mg; the common European grade to EN 755.
Both are non-heat-treatable, weldable and highly resistant to marine and industrial atmospheres. ASC LLP, Mumbai, supplies seamless and welded 5454 and 5754 pipes and tubes with EN 10204 3.1 certificates – please state the grade and standard on your enquiry.

What Grade Does “5054” Mean? – 5454 vs 5754 vs 5052
| Grade | Standard | Main alloying | Best for |
| AA 5454 | ASTM B241 / B221, ASME SB241 | Mg 2.4–3.0, Mn 0.50–1.0 | Welded pipe, tanks and vessels that run warm (above ≈ 65 °C) |
| EN AW-5754 (AlMg3) | EN 755, EN 573-3 | Mg 2.6–3.6 | General marine, chemical and structural tube to EN standards |
| AA 5052 | ASTM B210 (drawn tube), B241 | Mg 2.2–2.8, Cr 0.15–0.35 | Fuel, oil and hydraulic lines; drawn tube |
If a drawing or tender says “5054”, confirm with the designer which of these grades is intended. The chemistry and strength differ, so they are not interchangeable without approval.
Chemical Composition – 5454 and 5754 Pipes
| Element (wt %) | AA 5454 | EN AW-5754 |
| Magnesium (Mg) | 2.4 – 3.0 | 2.6 – 3.6 |
| Manganese (Mn) | 0.50 – 1.0 | 0.50 max |
| Chromium (Cr) | 0.05 – 0.20 | 0.30 max |
| Mn + Cr | – | 0.10 – 0.60 |
| Silicon (Si) | 0.25 max | 0.40 max |
| Iron (Fe) | 0.40 max | 0.40 max |
| Copper (Cu) | 0.10 max | 0.10 max |
| Zinc (Zn) | 0.25 max | 0.20 max |
| Titanium (Ti) | 0.20 max | 0.15 max |
| Others, each / total | 0.05 / 0.15 | 0.05 / 0.15 |
| Aluminium (Al) | Remainder | Remainder |


5054 / 5454 Aluminium Pipe Sizes & Schedules
| NPS | OD (mm) | Wall – SCH 40 (mm) | Wall – SCH 80 (mm) |
| ½” | 21.34 | 2.77 | 3.73 |
| ¾” | 26.67 | 2.87 | 3.91 |
| 1″ | 33.40 | 3.38 | 4.55 |
| 1½” | 48.26 | 3.68 | 5.08 |
| 2″ | 60.33 | 3.91 | 5.54 |
| 3″ | 88.90 | 5.49 | 7.62 |
| 4″ | 114.30 | 6.02 | 8.56 |
| 6″ | 168.28 | 7.11 | 10.97 |
| 8″ | 219.08 | 8.18 | 12.70 |
Aluminium pipe uses the same OD and wall as ASME B36.10 steel pipe. SCH 5, 10, 160 and metric tube sizes (OD × wall) are available on request.
Mechanical Properties of 5454 and 5754 Pipes
| Grade & temper | Tensile strength | Yield strength (min) | Elongation (min) | Standard |
| 5454-O | 215 – 285 MPa (31 – 41 ksi) | 85 MPa (12 ksi) | 14% | ASTM B241 / B221 |
| 5454-H111 | 230 MPa min (33 ksi) | 130 MPa (19 ksi) | 12% | ASTM B241 / B221 |
| 5454-H112 | 215 MPa min (31 ksi) | 85 MPa (12 ksi) | 12% | ASTM B241 / B221 |
| 5754-O / H111 | 180 – 250 MPa | 80 MPa | 14% | EN 755-2 |
| 5754-H112 | 180 MPa min | 80 MPa | 14% | EN 755-2 |
Values are specification minimums for extruded pipe and tube; exact limits depend on wall thickness and the edition of the standard. Drawn or cold-worked tempers (H32, H34) give higher strength.
AA 5054 Pipes Specifications
| Item | Details |
| Product | AA 5054 aluminium pipes & tubes (supplied as 5454 or 5754) |
| Pipe & tube standards | ASTM B241 / ASME SB241 (seamless), ASTM B221 / ASME SB221 (extruded), EN 755 |
| UNS / EN numbers | A95454; EN AW-5754 (AlMg3, 3.3535) |
| Type | Seamless, extruded, welded |
| Tempers | O, H111, H112; H32 / H34 for drawn tube |
| Size range | ½” to 12″ NB; metric OD tube on request |
| Schedule | SCH 5, 10, 40, 80, 160 |
| Length | Single random, double random, cut lengths |
| Ends | Plain, bevelled |
| Certificate | EN 10204 3.1; third-party inspection on request |
How to Order “5054” Aluminium Pipe Correctly
- Name the grade: 5454 (ASTM) or 5754 (EN). Avoid “5054” alone on a purchase order.
- Name the standard: ASTM B241 for seamless pressure pipe, B221 for extruded tube, or EN 755.
- State the temper: O or H112 for welded and formed systems; H111 where slightly higher strength is needed.
- Give size and wall: NPS and schedule, or OD × wall in mm.
- Ask for a 3.1 certificate showing chemistry and tensile results.
Need flanges or fittings for the line? See our aluminium flanges and aluminium fittings.
Physical Properties
| Property (approx.) | AA 5454 | EN AW-5754 |
| Density | 2.69 g/cm³ | 2.67 g/cm³ |
| Melting range | 602 – 646 °C | 600 – 640 °C |
| Thermal conductivity | ≈ 134 W/m·K | ≈ 130 W/m·K |
| Coefficient of expansion | ≈ 23.6 µm/m·°C | ≈ 23.7 µm/m·°C |
| Modulus of elasticity | ≈ 70 GPa | ≈ 69 GPa |
Applications of 5454 / 5754 Aluminium Pipes
| Industry | Typical uses |
| Marine & shipbuilding | Deck piping, fuel and water lines, rails and superstructure tube |
| Road tankers & transport | Welded tanks and piping for bulk liquids, including hot asphalt and chemicals (5454) |
| Chemical & process | Pressure vessels, storage tank piping, heat-exchanger tube |
| Food & beverage | Clean process lines where aluminium is approved |
| Construction | Handrails, structural tube and architectural sections |
Grades with more than about 3% Mg can become sensitive to intergranular corrosion if held above roughly 65 °C for long periods. 5454 keeps its Mg below 3% for this reason, so it is preferred for tanks and piping that run warm.
Why Buy 5054 / 5454 / 5754 Aluminium Pipes from ASC LLP?
- Right grade, clearly certified: we confirm 5454 or 5754 before order, and the 3.1 certificate states the exact grade and standard.
- Seamless and welded: see our aluminium seamless pipes and aluminium welded pipes.
- Matching plate: AA 5454 plates and AA 5754 plates for tanks and fabrication.
- Other pipe grades: AA 6061, AA 6063 and AA 6082 pipes.
- Export packing and regular shipments to the Middle East, Europe, USA and Asia.
Send grade, size, schedule, temper and quantity to sales@amardeepsteel.com or call 022-67439130.
Frequently Asked Questions – AA 5054 Pipes
Is AA 5054 a standard aluminium grade?
No. 5054 is not a registered Aluminum Association alloy and is not listed in ASTM B221, B241 or EN 573-3. It is used as a trade name; buyers normally mean 5454 (ASTM) or 5754 / AlMg3 (EN). Always confirm the grade before ordering.
What is the difference between 5454 and 5754 aluminium?
5454 contains 2.4–3.0% Mg and 0.50–1.0% Mn and is the ASTM pipe grade preferred for service above about 65 °C. 5754 contains 2.6–3.6% Mg with lower manganese and is the common European AlMg3 grade to EN 755.
What is the strength of 5454 aluminium pipe?
Under ASTM B241 / B221, 5454-O extruded pipe and tube require 215–285 MPa tensile strength, 85 MPa minimum yield strength and 14% minimum elongation.
What is the equivalent of 5754 aluminium?
EN AW-5754 is also known as AlMg3 and material number 3.3535, with UNS designation A95754.
Can 5454 and 5754 pipes be welded?
Yes. Both are non-heat-treatable 5xxx alloys with good weldability. 5554 or 5356 filler is commonly used for 5454; 5356 or 5183 for 5754, depending on the strength required.
Global Reach
ASC LLP supplies aluminium pipes, tubes, plates and fittings to marine, chemical, transport and construction customers worldwide, with prompt delivery and full documentation. Buyers in the USA, Europe, the Middle East and Asia rely on our AA 5054 / 5454 / 5754 aluminium pipes for certified material and traceability.

Countries We Export To
UNITED STATES, EUROPE, UK, UAE, SAUDI ARABIA, OMAN, KUWAIT, JORDAN, QATAR, INDONESIA, MALAYSIA, BRAZIL, SPAIN, ITALY, FRANCE, GERMANY, BAHRAIN, SRI LANKA, AZERBAIJAN, AUSTRALIA, AUSTRIA, PHILIPPINES, TURKEY, RUSSIA, IRAN, IRAQ, CANADA, KOREA, JAPAN, YEMEN, FINLAND, ZIMBABWE, HUNGARY, PORTUGAL, VIETNAM, MOROCCO, THAILAND, SOUTH AFRICA, MEXICO, SINGAPORE, GREECE, KUWAIT, POLAND, NEW ZEALAND, SWEDEN, SWITZERLAND, BELGIUM, BHUTAN, BANGLADESH, TAIWAN, ROMANIA, CAMBODIA, KAZAKHSTAN, AFGHANISTAN.

